Register Now

Login

Lost Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

Add question

Sorry, you do not have a permission to add a question .
You must login to ask question .

Login

Register Now

Vinyl sheet flooring installation method is easy and can be effortlessly achieved with correct procedures, tools and approach. Vinyl sheet floorings provides more choices as they are available in a variety of styles to accent your decor. This flooring is perfect for kitchens and bathrooms floors.

Procedure for Installation of Vinyl Sheet Flooring

Following procedures should be followed for installing vinyl sheet floors:

Health and Safety Measures for Vinyl Sheet Flooring

Before taking up the challenge make sure safety gears are in right place like knee pads as you must spend a lot of time working on your knees. Besides this, gloves and safety goggles are particularly essential as part of your safety kit.

Pay extra attention while using a utility knife and keep it covered when not in use. Ensure room is properly ventilated and kids are not in vicinity.

Safety Measures for Vinyl Sheet Flooring

Floor Preparation

The floor you intend to lay your sheet vinyl should be spotlessly devoid of any dust or debris. Sweep the floor properly and be certain that the surface is totally free of any protruding material like nails or screw heads. They can be removed using a hammer or a nail-puncher to push a nail below the floor surface.

Surface Preparations for Vinyl Sheet Flooring

In case your present floor is being treated with wood preservative then it’s not considered suitable for vinyl sheet covering. Presence of any oil, grease or bituminous solvent should be thoroughly removed by applying an appropriate cleaning agent.

A simple technique is employed to test whether a concrete floor is free of dampness or not if you plan to lay sheet vinyl on it. Place a plastic sheet of about one meter square in size and seal it on all sides. It should be kept in this condition overnight.

Any visible presence of any moisture underneath the plastic sheet signifies dampness which must be rectified before laying the sheet vinyl. If the concrete floor is uneven it is better to level the floor first, take guidance on how to level a concrete floor.

Moisture Removal from Floor Surface

Accurate Measurement of Floor Dimensions

Measure the length and width of the room. Make sure the dimensions measured are accurate. Precise measurement of room dimensions is required because sheet vinyl is purchased and fitted based on these dimensions.

Measure right up to the center of doors where it comes. Allow 75 mm extra to each edge for proper cutting and trimming. For most rooms, you need 1 sheet of vinyl floor.

Measurement of Floors for Vinyl Sheet Flooring

Installations of Sheet Vinyl Flooring

Even before you start laying your sheet vinyl, unroll it on the room floor and leave it there for next 24 hours so that it adjusts to the surface conditions. Rough lay your vinyl and properly adjust it on the floor so that it fits closely allowing 75mm access.

Laying vinyl in bathroom area can be tricky. Near the pedestal region like toilet and sink, vinyl sheet needs to be cut around them. For this a series of slits are made in the vinyl around the pedestal and vinyl sheet is cut in the shape of the pedestal to adjust that location.

Then vinyl is pressed down and the flaps are folded up around the pedestal. The excess is trimmed with knife to make it perfect fit. Continue to work around the room with each pedestal or any other sort of obstacle you come through.

Procedure for Vinyl Sheet Flooring Installation

Once the sheet is perfectly fixed around the pedestal, you must work around the room trimming the edges. Use a vinyl cutter because that will give you a clean finish edge. If possible, avoid cutting around in wet area as water can go underneath it and can damage the vinyl.

The important point to remember is that all sheets vinyl flooring needs to be perfectly stuck to the floor. Depending on the kind of sheet vinyl it can either be fully bonded to the floor using an appropriate vinyl adhesive that is sprayed on the floor or be bonded at the perimeter and joined using double sided vinyl floor tape.

Normally cushion type sheet vinyl needs to be bonded at the perimeter and non-cushion sheet vinyl needs to be fully bonded. However, it is necessary to follow manufacturer’s instruction.

Suppose you select a perimeter vinyl type, then you should be able to handle a double-sided tape to the floor for final fitting of the sheet vinyl. You can straight away stick the double-sided tape on the floor if the surface is non-porous and damage free.

Though it is very difficult to find such a floor and so you can spray adhesive under the tape. First read the instructions and safety procedures mentioned on the adhesive tube. Spray the adhesive along the edge of the floor taking care not to spray on the walls.

Adhesive for Vinyl Sheet Flooring

Follow this by sticking the tape around the edges of the room. Use a smooth block of wood to run on top of the tape to ensure its firmly fixed.

Tape for Vinyl Sheet Flooring at Edges

Repeat this procedure for the other edges and use tape around the base of pedestal and any other obstructions.

Tape for Vinyl Sheet Flooring at Edges

Finally, sheet vinyl can be laid. Gently lift each edge and remove the backing paper of the tape and stick vinyl firmly on the floor.

Laying of Vinyl Sheet Flooring

Finishing Touches for Vinyl Sheet Flooring

While fixing vinyl sheet in a wet area like bathroom you can seal the joint between the sheet vinyl and floor with sanitary grade silicon sealant. Make sure that the sealant nozzle is properly cut before use. The bigger the gap the bigger is the nozzle cut. Start one end and move along continuous edge maintaining a steady pressure and speed.

Finishing of Vinyl Sheet Flooring

To smooth the sealant, you can use the sealant shaper or wet soapy finger but remember to wear gloves. Another option is to fit a trim between the edge of the floor and wall. Installing T-bars between sheet vinyl at the doorway of two different rooms for clean finish is a great idea too.

With these easy-to-use methods, you can perfectly fix vinyl sheet in your home. You can even find all the required material and tools easily in a nearby market or online with quality information and price comparisons.

Read More on Flooring Methods