TO DETERMINE SPECIFIC GRAVITY OF THE SOLIDS BY DENSITY BOTTLE METHOD

Theory;

The specific gravity of solid particles is the ratio of the mass density of solids to that water. It is determined in the laboratory using the relation:

SPECIFIC GRAVITY OF THE SOLIDS BY DENSITY BOTTLE METHOD

Where

M1 = mass of empty bottle

M2 = mass of the bottle and dry soil

M3 = mass of bottle, soil and water

M4 = mass of bottle filled with water only.

Equipment:

1. 50ml density bottle with stopper

2. Oven (105 0 to 110 0C)

3. Constant temperature water bath (27 0C)

4. Vacuum desiccator

5. Vacuum pump

6. Weighing balance accuracy 0.001g

7. Spatula

Procedure:

1. Wash the density bottle and dry it in an oven at 105 0C to 100 0C. Cool it in the desiccator.

2. Weigh the bottle, with stopper to the nearest 0.001g (M1).

3. Take 5 to 10g of the oven dried soil sample and transfer it the density bottle. Weigh the bootle with the stopper and the dry sample (M2).

4. Add de-aired distilled water to the density bottle just enough to cove the soil. Shake gently to mix the soil and water.

5. Place the bottle containing the soil and water after removing the stopper in the vacuum desiccator.

6. Evacuate the desiccator gradually by operating the vacuum pump. Reduce the pressure to about 20 mm of mercury. Keep the bottle in the desiccator for at least 1 hour or until no further movement of air is noticed.

7. Replace the vacuum and remove the lid of the desiccator. Stir the soil in the bottle carefully with a spatula. Before removing the spatula from the bottle, the particles of soil adhering to it should be washed off with a few drops of air free water. Replace the lid of the desiccator and again apply vacuum. Repeat the procedure until no more air is evolved from the specimen.

Note: In case of vacuum desiccator is not available, the entrapped air can be removed by heating the density bottle on a water bath or a sand bath.

8. Remove the bottle from the desiccator. Add air-free water until the bottle is full. Insert the stopper.

9. Immerse the bottle upto the neck in a constant-temperature bath for approximately 1 hour or until it has attained the constant temperature.

If there is an apparent decrease in the volume of the liquid in the bottle, remove the stopper and add more water to the bottle and replace the stopper. Again place the bottle in the water bath. Allow sufficient time to ensure that the bottle and its content attain the constant temperature.

10. Take out the bottle from the water bath. Wipe it clean and dry it from outside. Fill the capillary in the stopper with drops of distilled water, if necessary.

11. Determine the mass of the bottle and its contents (M3).

12. Empty the bottle and clean it thoroughly. Fill it with distilled water. Insert the stopper.

13. Immerse the bottle in the constant-temperature bath for 1 hour or until it has attained the constant temperature of the bath.

If there is an apparent decrease in the volume of the liquid, remove the stopper and add more water. Again keep it in the water bath.

14. Take out the bottle from the water bath. Wipe it dry and take the mass (M4).

Observations and calculations:

Sl. No.

Observations an Calculations

Determination No.

1

2

3

Observation

1

Density bottle No.

 

 

 

2

Mass of empty density bottle (M1)

 

 

 

3

Mass of Mass of bottle dry soil (M2)

 

 

 

4

Mass of bottle, soil and water (M3)

 

 

 

5

Mass of bottle filled with water (M4)

 

 

 

Calculations

6

M2 – M1

 

 

 

7

M3 – M4

 

 

 

8

Calculate G using formula

 

 

 

Result:

Specific gravity of solids = _____.