🕑 Reading time: 1 minutePainting on a surface is not same for all surface types. Some precautions are to be taken before and after painting. Methods and process of painting on different surfaces are discussed.
- Methods and Process of Painting on Different Surfaces
- Painting on New Wood Work
- Repainting of Old Wooden Surface
Methods and Process of Painting on Different Surfaces
- New wood work
- Repainting Old wood surface
- New iron and steel surfaces
- Repainting of old steel and iron surfaces
- Galvanized iron surface
- Plastered surfaces
Painting on New Wood WorkFollowing are the steps for painting new wooden surfaces:
- Surface preparation
- Under coating
1. Surface Preparation of Wooden WorksThe surface should be well cleaned without any dust, spots, greasy matter etc. The nails used in the wood work should be punched up to 3mm below the surface. The wood in wood work should be well seasoned and should not contain more than 15% of moisture content. The surface should be dry.
2. KnottingKnots present in the wood may eject resins from wood. So, knots are killed or covered in this knotting process. Knotting can be done by two ways as follows: 1. In this first method, two coats of solutions are applied on surface. First coat consists 15g of red lead, 2 liters of water and 225 grams of glue. After adding these three, mixture is heated and applied and left for 10 minutes. After that second coat is applied which consists red lead ground in boiled linseed oil and thinned with turpentine oil. 2. In this method, hot lime coat is applied on surface and left it for 24 hours. After that the layer is scrapped off from the surface.
3. Priming of New Wooden SurfacePriming is nothing but applying prime coat or first coat on surface. In this case, the surface is smoothened with abrasive paper and then first coat of paint is applied to fill all the pores in the surface. The ingredients used in this prime coat is same as subsequent coats but the quantity or composition ratio may vary.
4. StoppingAfter filling all the pores of wooden surface in priming, it’s time to fill up nail holes, dents, cracks, etc. Putty is used as the fill material. When putty is dried, then the whole surface is rubbed with glass paper or pumice stone. This process of rubbing sown the wooden surface is called stopping.
5. Under Coating of New Wooden SurfaceIn general, for good quality works, 4 coats of paints are applied (prime + under coatings + finishing). For inferior quality works 2 to 3 coats can be used. So, under coatings are nothing but second and third coats of good quality works which provides same look or shade as finishing coat. For better results, enough time should be allowed for each coat.
6. Finishing of New Wooden SurfaceFinishing is the last coat applied on surface which is generally applied on the under coatings. It should be applied in smooth, uniform manner. It decides the whole final look of surface, so, skilled workers is required for better results.
Repainting of Old Wooden SurfaceOld wood work can be repainted but the previous paint work should be removed. The removal is more important which can be done by many ways as follows:
- Prepare a solution of 1 kg caustic soda in 5 liters of water and apply on the old painted surface. When this solution is applied on the surface, the old paint gets dissolved and removed easily.
- Another method is, prepare a hot solution consisting of soft soap, potash, quicklime in the ratio 1:2:1. This solution is applied on old surface and washed with hot water.
- 1:1 mixture of washing soda and quick lime is prepared and applied on old paint surface and then washed with water.
Painting of New Iron and Steel SurfacesPainting of iron and steel surfaces will resist the rust formation due to weathering. Before painting the surface must be cleaned. If there is any rust or scales, should be wiped off using steel brushes etc. stains on surface can be washed with benzene or lime water. Before applying prime coat, the surface should be treated with phosphoric acid to get better adhesive nature. Now prime coat is applied which consists 3kg of red lead in 1 liter of boiled linseed oil. This should be applied using brush. After that, two or more under coats are applied which consist 3 kg of red lead in 5 liters of boiled linseed oil. After drying up, smooth finishing coat of desired paint is applied.
Repainting of Old Steel and Iron SurfacesRepainting of steel and iron surfaces is as same as new surfaces but cleaning of old paint is most important. Oxy acetylene flame is used to burn off the paint surface and then it is scrapped with brushes.
Painting of Galvanized Iron SurfaceIn general, Galvanized iron surface does not contain adhesive nature with paint. So, it is difficult to apply paint on it without any special action. That special treatment may be applying different solutions on surface. The solutions are 40 grams of copper acetate in one liter of water or 13 grams each of copper chloride, copper nitrate, muriatic acid and ammonium chloride in 1 liter of water. Any one of these two solutions are mixed in earthen vessel and applied on surface. When the surface turns into black, then prime coat is applied after it dries, finishing coat is applied.
Painting of Plastered SurfacesPainting of newly plastered surfaces is difficult because of moisture content present in the plaster material. Heat of hydration of cement also causes severe problems for paints especially oil based paints and distempers are liable to alkali attack. To overcome this, alkali resistant primer is used in prime coat. The plastered surface contains pores in it, and whenever the paint is applied, liquid from the paint is absorbed by these pores which is called as suction. The suction of surface depends upon type of paint, prime coat composition, etc. Suction should be uniform throughout the surface. S0, the preparation of surface depends upon the type of paint used on the surface. For different paints, different types of pretreatments are adopted on the surface which is described in below table.
|Type of paint||Preparation of surface|
|Oil paint||A coat of thin primer or prime sealer|
|Emulsion paint||A coat of paint thinned with water|
|Dry distemper||Same distemper thinned with water|
|Size bound distemper||A Coat of clearcole|
|Cement paint and lime wash||Just wet the surface before applying.|