Sign Up

Sign Up to The Constructor to ask questions, answer people’s questions, write articles, and connect with other people. VIP members get additional benefits.

Sign In

Login to The Constructor to ask questions, answer people’s questions, write articles & connect with other people. VIP members get additional benefits.

Forgot Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

Sorry, you do not have permission to ask a question, You must login to ask question. Become VIP Member

Get More Features, Sign Up Now. Become VIP Member

Print, PDF & Email

There are various types of joints in water retaining structures during construction. Sealing materials for joints in these structures are discussed.

There are three types of joints in concrete construction, viz. construction joint, expansion joint and contraction joints. Learn more about Joints in Concrete Structures.

Materials for Sealing Joints in Water Retaining Structures

(1) Materials for joints in water retaining structures and water tight structures for sewage and effluent treatment shall be resistant to aerobic and anaerobic microbiological attack and resistant to attack by petrol, diesel oil, dilute acids and alkalis.

(2) Materials for joints in water retaining structures for potable and fresh water shall comply with the requirements of BS 6920.

Joint filler

Joint filler shall be firm, compressible, single-thickness, non-rotting filler. Joint filler for joints in water retaining structures and watertight structures shall be non-absorbent.

Bitumen emulsion

Bitumen emulsion for joints in water retaining structures and watertight structures shall comply with BS 3416. Bitumen emulsion for surfaces against which potable or fresh water will be stored or conveyed shall comply with BS 3416, type II.

Fig: Joints in concrete structures

Joint sealant

(1) Joint sealant shall be a grade suited to the climatic conditions of Hong Kong and shall perform effectively over a temperature range of 0°C to 60°C. Joint sealant for exposed joints shall be grey.

(2) Joint sealant other than cold-applied bitumen rubber sealant shall be:

(a) A gun grade for horizontal joints 15 mm wide or less and for vertical and inclined joints,

(b) A pouring grade for horizontal joints wider than 15 mm.

(3) Polysulphide-based sealant shall be a cold-applied two-part sealant complying with BS 4254. Polysulphide-based sealant for expansion joints in water retaining structures and watertight structures shall have a transverse butt-joint movement range of at least 20%.

(4) Polyurethane-based sealant shall be a cold-applied two-part sealant complying with the performance requirements of BS 4254.

(5) Hot-applied bitumen rubber sealant shall comply with BS 2499, type N1.

(6) Cold-applied bitumen rubber sealant shall be of a proprietary type.

(7) Joint sealant for joints in water retaining structures and water tight structures shall be as stated in Table-1.

(8) Primers and caulking material for use with joint sealant shall be of a proprietary type recommended by the joint sealant manufacturer.

(9) Different types of joint sealant and primers that will be in contact shall be compatible.

Table-1: Joint sealant for water retaining structures and water tight structures

Structure for retaining / excluding Type of joint Type of joint sealant
Sewage All joints Polyurethane based
Other than sewage Expansion joint Polyurethane based or Polysulphide based
Horizontal joints other than expansion joints Hot applied bitumen rubber, Polysulphide based or polyurethane based
Vertical and inclined joints other than expansion joints Polysulphide based, polyurethane based or cold-applied bitumen rubber

Bond breaker tape

Bond breaker tape shall be of a proprietary type recommended by the joint sealant manufacturer and approved by the Engineer. The tape shall be a polyethylene film with adhesive applied on one side and shall be the full width of the groove.

Bearing strip for sliding joints

Bearing strip for sliding joints shall consist of two plastic strips of a proprietary type approved by the Engineer. The strips shall be resistant to all weather conditions and to chemicals to which the structure will be subjected without impairing the reaction, durability or function of the strips.

The strips shall be of a type that will not require maintenance after installation. The strips shall be capable of withstanding a vertical load of at least 300 kN/m2 and shall have a maximum coefficient of friction of 0.3 under a constant shearing force.

Waterstops or water stoppers

Waterstops, including intersections, reducers and junctions, shall be of a proprietary type approved by the Engineer. Waterstops shall be natural or synthetic rubber or extruded polyvinyl chloride and shall have the properties stated in Table-2.

Table-2: Properties of waterstops or water stoppers

Property of water stops Rubber waterstops PVC waterstops
Density 1100 kg/m3 (+/-5%) 1300 kg/m3 (+/-5%)
Hardness 60 – 70 IRHD 70 – 90 IRHD
Tensile strength >/= 20 N/mm2 >/= 13 N/mm2
Elongation at break point >450% >285%
Water absorption <5% by mass after 48 hours immersion <0.15% after 24 hours immersion
Softness number 42 – 52

While principles of concrete joints remains same, references may also be made to ACI 224.3R-95 Joints in Concrete Construction and IS:3414 – 1968 – Indian Standard Code of Practice for Design and Installation of Joints in Buildings (Reaffirmed in 2010).

Read More:

Joints in Liquid Retaining Structures

Various Types of Joints in Concrete Construction

Sealing of Various Types of Joints in Building Construction

Types of Sealants Used for Joints in Buildings -Properties, Uses, Working

Sign up to email updates and Get Free Ebook on Concrete Repair Methods, Techniques and Guidelines.

Gopal Mishra

Gopal Mishra

Gopal Mishra is a Civil Engineer from NIT Calicut and has more than 10 years of experience in Civil Engineering and Construction. He is the founder of The Constructor.

Related Articles

3 Comments

Leave a comment

You must login to add a new comment.